• Setting up Remote syslog with Kiwi

    Locked
    4
    0 Votes
    4 Posts
    4k Views
    C

    I wouldn't recommend disabling local logging, unless you have a specific reason for doing so. It's usually desirable to be able to see the logs from the webGUI as well as on your syslog server.

    Your config is fine, my first guess is as onhel suggested, a firewall on the machine.

  • Share the same phisical network?

    Locked
    4
    0 Votes
    4 Posts
    2k Views
    H

    Here is a HOWTO

    http://doc.pfsense.org/index.php/HOWTO_setup_vlans_with_pfSense

  • Can all FreeBSD packages be installed on pfSense, and what makes sense?

    Locked
    2
    0 Votes
    2 Posts
    2k Views
    Cry HavokC

    This has been discussed before, and the response is that you're on your own if you do.  It's completely unsupported.

    I would say that I strongly disagree with your final sentence.  The most you should ever install on a firewall would be a proxy server or VPN endpoint.  You should never run FTP/HTTP servers etc.

  • Creating new rrd graphic

    Locked
    1
    0 Votes
    1 Posts
    1k Views
    No one has replied
  • 0 Votes
    2 Posts
    2k Views
    D

    look at

    http://forum.pfsense.org/index.php/topic,6335.msg36526.html#msg36526

  • BGP Support

    Locked
    1
    0 Votes
    1 Posts
    2k Views
    No one has replied
  • Remote logging format

    Locked
    2
    0 Votes
    2 Posts
    2k Views
    D

    Hmm, 0 responses?  Oh well it's no longer relevant (to me).  I was forced by another decision to use a different router.  :'(

  • Check_reload_status and nothing more…

    Locked
    3
    0 Votes
    3 Posts
    2k Views
    G

    Was a bad memory card….  :-\

    Thanks for your help,

  • How to block all P2P….????

    Locked
    14
    0 Votes
    14 Posts
    5k Views
    Cry HavokC

    Have you checked the "Block offenders" option?

  • OpenNTPD configuration (v. 1.2-RC2 embedded)

    Locked
    4
    0 Votes
    4 Posts
    2k Views
    K

    I applogize this is slightly off topic.
    I was reading this thread trying to figure out if i may have an issue and find that the ntp engine is running however it hasnt updated in two days. the last time it updated was when i installed pfsense
    Sep 24 21:37:42 ntpdate[251]: adjust time server 219.117.196.238 offset -0.061082 sec
    I searched for a little insite into how offen it updates and possible problems.
    I know the clock wasnt that far off but in two days there should be some drift to show in an update.

  • Copy rules from one interface to another?

    Locked
    6
    0 Votes
    6 Posts
    4k Views
    F

    I ended up using a combination of both. I filled out the remaining rules I hadn't already rebuilt by hand using the "new rules based on this one" button, then did some cut/paste and find/replacing in config backups to fill out opt2-4.

    Thanks again to you both.

  • Need to resolve issues with Avast Home Edition!

    Locked
    2
    0 Votes
    2 Posts
    2k Views
    D

    take a look

    http://forum.pfsense.org/index.php/topic,6270.msg36212.html#msg36212

  • 0 Votes
    5 Posts
    2k Views
    C

    It's a 32 bit counter. It'll be that way until it's changed in FreeBSD.

  • How to change SSH banner? [SOLVED…the ugly way]

    Locked
    6
    0 Votes
    6 Posts
    24k Views
    J

    Danny

    You should never remove the SSH-2.0-OpenSSH_4.5p1. Some SSH clients use this to figure out what options your SSHD server supports. In the past I have changed  SSH-2.0-OpenSSH_4.5p1 too SSH-2.0 and never encountered a SSH client that brakes because of that change, but you never know. The clean way to change the SSH-2.0-OpenSSH_4.5p1 is to edit the SHHD source code.

    laterz
    JamesDean

  • PfSense & HAVP + Clam…

    Locked
    1
    0 Votes
    1 Posts
    2k Views
    No one has replied
  • VLAN problem (long) [solved kind of]

    Locked
    6
    0 Votes
    6 Posts
    3k Views
    B

    OK. Great to hear!

    BTW: Just for the records, can you mention what brands the working and the notworking switches are?

    Thanks!

  • Install R-U-ON ServerOn agent

    Locked
    1
    0 Votes
    1 Posts
    1k Views
    No one has replied
  • Block orkut

    Locked
    5
    0 Votes
    5 Posts
    3k Views
    Cry HavokC
    Install squid Block all outbound access via the firewall to 80/tcp and 443/tcp Configure squid to block access to www.orkut.com
  • LAN interface stops working / "sendto: no buffer space available"

    Locked
    10
    0 Votes
    10 Posts
    4k Views
    S

    Check the snapshot server in a bit and the new ISO should include the changes.

  • Strange Download behavior with Mac OS X client

    Locked
    2
    0 Votes
    2 Posts
    1k Views
    bill_mcgonigleB

    Can you post a specific URL to try?

Copyright 2025 Rubicon Communications LLC (Netgate). All rights reserved.