Thank you, I will keep an eye on it and gather the necessary info if it happens again.  As of right now, I have not had a problem since yesterday around noon, but will monitor the situation. As a side note, when my Web GUI freezes in my situation, I don't get a "502 Bad Gateway" error, the web page doesn't load and the cursor just keeps spinning.  That doesn't mean it's not the same issue though. Thanks again, jimp.

I would be very glad to learn how you have successfuly configured transparent HTTP (S) proxy along with AD (which I translate as "authentication")

It is not a bug. Host addresses that are defined as a monitor IP address have a specific host route out the interface they are defined on. Same thing with DNS servers in System > General if you define a gateway there. This is necessary for Multi-WAN, which is a feature people seem to like.

Hi, I have the same issue. Frustrating: at the end of the upgrade process it sais "You can find instructions on how to convert it" but not where  :-[ I'm going to give these instructions a go and let you know if it worked: https://doc.pfsense.org/index.php/Upgrading_64-bit_NanoBSD_2.3_to_2.4

@CubedRoot: jimp, I have attached the text files in this reply. I have not yet reinstalled, as I am right now booting the unit to the kernel.old to get it running. Exactly the same problem (failed with same error after upgrade, works with kernel.old) Motherboard : ASRock D1800M (Celeron Processor J1800) NIC (not working after upgrade and new kernel)  : Intel EXPI9301CTBLK (PCIe), SYBA SY-PEX24028 Dual Port (PCIe, Realtek Chipset 8111E) NIC (working after upgrade and new kernel) : Realtek RTL8111GR (integrated)

Problem solved with your sugestion ;)

Thank you - should have looked more thoroughly thru the forum.

After activating ipv6 on one more interface and touching WAN config the NAT error is gone. Even after reverting the changes. I think pfsense should boot twice after upgrading.

Since this from May I doubt he is still working on this problem ;)

Did the upgrade and everything went without a hitch. I actually tested it in vmware first, loaded my config to make an identical setup.  Worked flawlessly there, so I did the upgrade on my home production box. Only thing I had to do was hit SHIFT+F5 in chrome to make the pfsense logo back to the normal size in the upper right corner. All packages updated as well.

That's unrelated to this issue, please start a new thread.

With regards to the download speed. It appears that the new version of firefox slows the download. Using other browsers like chrome and opera does not seem to limit the download so the speed issue can't be on PFSense. The upgrade as seen from the GUI went well, the problem occurred after reboot. The interfaces are not detected and I was just prompted with setting the interfaces dialogs. Anyway, as I was able to easily recover by installing from scratch and restore from backup xml file, everything is back to normal here.

@jimp: If you want to stay on 2.3.x, you must go to System > Update, Update Settings tab and select the security/errata branch, then you can make changes to packages. Otherwise you'll have to update to 2.4 first, which will pick up any updates automatically along the way.

pfsense 2.4.0-RELEASE (amd64) does support UASP. #camcontrol devlist <st1000nm 0011="" pt0d="">at scbus0 target 0 lun 0 (pass0,da0) #camcontrol inquiry da0 pass0: <st1000nm 0011="" pt0d="">Fixed Direct Access SPC-4 SCSI device pass0: Serial Number 000000123BA3 pass0: 400.000MB/s transfers #usbconfig ugen0.1: <0x8086 XHCI root HUB> at usbus0, cfg=0 md=HOST spd=SUPER (5.0Gbps) pwr=SAVE (0mA) ugen0.2: <vendor 0x05e3="" usb2.0="" hub="">at usbus0, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE (100mA) ugen0.3: <vendor 0x04d9="" usb="" keyboard="">at usbus0, cfg=0 md=HOST spd=LOW (1.5Mbps) pwr=ON (100mA) ugen0.4: <vli manufacture="" string="" vli="" product="">at usbus0, cfg=0 md=HOST spd=SUPER (5.0Gbps) pwr=ON (2mA)</vli></vendor></vendor></st1000nm></st1000nm> This is with this USB to SATA device and this HDD. My next mission is to figure out how to test the actual speed it achieves. Edit: build in speed test: #diskinfo -tv /dev/da0p2 /dev/da0p2 512        # sectorsize 996431888384 # mediasize in bytes (928G) 1946156032  # mediasize in sectors 0          # stripesize 544768      # stripeoffset 121142      # Cylinders according to firmware. 255        # Heads according to firmware. 63          # Sectors according to firmware. 000000123BA3 # Disk ident. Seek times: Full stroke:   250 iter in  5.089351 sec =  20.357 msec Half stroke:   250 iter in  3.598658 sec =  14.395 msec Quarter stroke:   500 iter in  5.795468 sec =  11.591 msec Short forward:   400 iter in  1.517583 sec =    3.794 msec Short backward:   400 iter in  2.655790 sec =    6.639 msec Seq outer: 2048 iter in  1.572585 sec =    0.768 msec Seq inner: 2048 iter in  1.577754 sec =    0.770 msec Transfer rates: outside:      102400 kbytes in  0.831469 sec =  123156 kbytes/sec middle:        102400 kbytes in  0.863127 sec =  118638 kbytes/sec inside:        102400 kbytes in  1.456835 sec =    70289 kbytes/sec

Deleted the file, went to the gui saved it, the file showed up, same error. : id uid=2000(xxxx) gid=65534(nobody) groups=65534(nobody),1999(admins)