Subcategories

• Cache/Proxy

  Discussions about packages which handle caching and proxy functions such as squid, lightsquid, squidGuard, etc.
  4k Topics

  21k Posts

  E

  I even tried deleting and creating a new certificate. Any suggestions?
• IDS/IPS

  Discussions about packages whose functions are Intrusion Detection and Intrusion Prevention such as snort, suricata, etc.
  2k Topics

  16k Posts

  G

  As the title says. Any mirror or alternative ? https://feodotracker.abuse.ch/blocklist/ Error 503 certificate has expired certificate has expired Error 54113 Details: cache-scl2220043-SCL 1757230189 2309835888 Varnish cache server
• Traffic Monitoring

  Discussions about packages that handle bandwidth and network traffic monitoring functions such as bandwidtd, ntopng, etc.
  572 Topics

  3k Posts

  K

  @Antibiotic No it’s not possible with NtopNG as it is not a Netflow collector. You need nProbe for that which will “translate” recieved netflows into flows that NtopNG understands and can visualize (with very very little detail might I add as Netflows has no additonal information apart from sender/reciever and volume). The NtopNG package and the product in general is more geared towards visualising and recording traffic details from actual packet captures. This contains MUCH more metadata about the sessions than netflows (DNS names, protocol information and myriads of other things). But pffSense Plus has a builtin Netflow exporter if you have an external netflow collector on hand.
• pfBlockerNG

  Discussions about the pfBlockerNG package
  3k Topics

  20k Posts

  J

  @nanda said in pfb_filter and pfb_dnsbl services are not running Pfsense 25.07.1: When I checked the status of the service, the firewall returned, "does not exist". as in on the Status -> Services page? or where specifically ? and yet it shows on the dashboard services widget.. And you said this was a fresh install so ... are there any errors in pfblockerNG 's error.log, dnsbl_parsed_error or py_error (Firewall -> pfBlockerNG -> Logs on the pfblockerNG -> General. make sure the Keep Settings option is enabled then head over to packages and try to reinstall the package (you may remove and install or just reinstall) see if you spot any install errors during the install then when complete you will need to change the masterfile / mastercat line again and then check the update page at Firewall -> pfBlockerNG -> Update should have a status showing the next scheduled cron event (if that is within a few minutes just wait for it to run). if it is more than say 20 minutes away or says not scheduled (or similar) then on the same update screen force Cron hit run. when that is complete check the status then reboot check the status
• UPS Tools

  Discussions about Network UPS Tools and APCUPSD packages for pfSense
  101 Topics

  2k Posts

  D

  @jhg said in NUT fails to start after 2.7.2 -> 2.8.0 upgrade: Interesting. I would have thought the initial reboot, which occurred as part of the upgrade, would have done the trick, but it took a second reboot, just now, to get things working. Glad you have it sorted. There was no difference in the output of usbconfig show_ifdrv at any point -- before or after unplugging/replugging the USB cable, nor after rebooting. ... Question: What would tell me whether or not a driver was loaded? If there were an attached driver, it should have shown up with the show_ifdrv command. If you use the command and look at the other usb devices, I think they will show attached drivers. I don't expect to see a driver attached to the ups, because there is a quirk that tells the OS to ignore that device (and not attach a driver). Look for idVendor and idProduct in the above output. The Vendor ID for your device is 0764, which corresponds to Cyber Power Systems, and the Product ID for your device is 0601, which is registered as "PR1500LCDRT2U UPS" (don't sweat an exact match for the name). You can see the quirk with the following command: [25.07-RC][root@fw]/root: usbconfig dump_device_quirks | grep 0764 VID=0x0764 PID=0x0005 REVLO=0x0000 REVHI=0xffff QUIRK=UQ_HID_IGNORE VID=0x0764 PID=0x0501 REVLO=0x0000 REVHI=0xffff QUIRK=UQ_HID_IGNORE VID=0x0764 PID=0x0601 REVLO=0x0000 REVHI=0xffff QUIRK=UQ_HID_IGNORE [25.07-RC][root@fw]/root: Your device is third on the list. The HID_IGNORE quirk says to ignore the device and not attach a driver. @jhg said in NUT fails to start after 2.7.2 -> 2.8.0 upgrade: You might consider adding this resolution to the release notes for 2.8. LOL... sorry, I don't have input to the release notes (I don't work here). While I wrote and maintain various packages, including NUT, I'm still just a volunteer. Most packages are actually written by volunteers.
• ACME

  Discussions about the ACME / Let’s Encrypt package for pfSense
  500 Topics

  3k Posts

  G

  @Gertjan well..... finally i created a new user for inwx and just gave him dns_management role only AND without 2FA. So now all is fine, my PFSense has the LE Cert as it should be. Thanks and kr Mike
• FRR

  Discussions about the FRR Dynamic Routing package on pfSense
  294 Topics

  1k Posts

  Y

  said in Please update frr on Pfsense+ to FRR 10.3: https://redmine.pfsense.org/issues/15785 now frr 10.4.1
• Tailscale

  Discussions about the Tailscale package
  90 Topics

  609 Posts

  L

  The bugaboo that was affecting the FreeBSD 15 pkg repos has cleared, and the new builds seem to be finished. So, 1.86.4 is now landed in FreeBSD:15:amd64/latest ABI: pkg add -f https://pkg.freebsd.org/FreeBSD:15:amd64/latest/All/tailscale-1.86.4.pkg
• WireGuard

  Discussions about WireGuard
  699 Topics

  4k Posts

  S

  @Bob.Dig what's the right place?