It will boot up to fully working state on 64 mb BUT you will encounter random process killing later when you push it too hard or use too many features. If you get it booting you should add some RAM to make it run fine.

yeah, it wouldn't just be for routing heh, of course it'd be doing other tasks, and these are xeon MP's, more like hyper threading than dual core, but still shows up as 8 heh

thanks for the input

Josh

The driver has to support altq and the axedriver simply doesn't. See http://forum.pfsense.org/index.php/topic,16.msg35.html#msg35 for a list of compatible drivers. With this nic you can't do trafficshaping but it will be fine when using without trafficshaping (besides that usb is pretty slow and might cause some other issues; freebsd's usb support is not that great atm).

thanks jeroen234
I'll bet that is what I am seeing.

I upgraded from RC2 to RC3 using the full upgrade and I had done the same for RC2.

I have an optional interface running, traffic shaping, and a separate package (ntop) running.
I'm betting this is just using the extra memory.  It stays around 60% so I'm not worried.

thanks for the input

@box_l:

hi,

for those of you who are interested, the type of null modem cable required to see the BIOS is shown on

http://www.lammertbies.nl/comm/info/RS-232_null_modem.html

about half way down "Null modem with partial handshaking"

i had to make my own as i tried about 8 cables from colleagues and friends to no avail.

very satisfying when it worked, i can now boot from a cd on a dual connector ide and should be able to install direct. (if the installer outputs to the serial console correctly!)

BoX

Nice to know. Didn't know there was soo many different kinds. I just bought one off ebay for a few bucks and it works great. Can get into the BIOS too.

@Phusho:

My problem is overpowered CPU on 266 Mhz ;) must change the system if have problems with more traffic for now it is not issu\

Edit: the numbers from the previous post are time 10 bigger it is for 30 Mbit/s when pfsense is at 100 % not 3 with m0n0wall top speed with the same system is about 50-60 Mbit/s. 30 Mbit/s is more than enough for the current use :) 10x for reading.

A 266 MHz, if we're talking about a WRAP or Soekris 4801, will push about 30-32 Mbps with pfsense, and 40-45 Mbps with m0n0wall.  If it's a generic PC with a 266 MHz proc, numbers will vary depending on what type of machine, what NIC's, etc.

Those numbers are for an optimal transfer - single TCP stream, optimal packet size, etc.

Depends, you won't get a bios labeled year 2006 but in case you get an old version that is still newer than the one you have I would give that a try.

I used http://netgear.com/Products/RoutersandGateways/WiredRouters/DG632.aspx?detail=Specifications several times already. Supports Bridgemode, bridgemode with router doing the pppoe only (probably what you need though I have not tested this yet) or routing mode including DMZ IP.

DMZ (opt1) : Bridge with none, 10.1.1.1 / 24
LAN : Bridge with DMZ, 192.168.2.1 / 24

wai is the lan bridged with dmz ?, this will make from 2 subnets only 1?

There are quite a few ARM board resellers, here's one without mini-PCI:

http://www.embedian.com/index.php?main_page=product_info&cPath=1_17&products_id=181

And a selection for AP's:

http://www.compex.com.sg/home/OEM/product_ap.htm

Expensive developer board:

http://shop.directinsight.co.uk/catalog/product_info.php?products_id=799

So its probably more of a wait and see which manufacturer has a reliable and popular yield at reasonable price similar to WRAP.

@Willem:

I am getting no carrier on the WAN, right after plugging in WAN it loses connection. I have tried to change config.xml like;

<media>100 base TX
<mediaopt>full duplex</mediaopt>

Looking at ifconfig its says autoselect none</media>

I doubt that these options are correct. Did you run ifconfig -m to see the valid options for your NIC?
For example, a sis interface on a wrap shows these options:

sis0: flags=8943 <up,broadcast,running,promisc,simplex,multicast>mtu 1500 options=8 <vlan_mtu>capabilities=48 <vlan_mtu,polling>inet 192.168.1.1 netmask 0xffffff00 broadcast 192.168.1.255 inet6 fe80::20d:b9ff:fe01:2c8%sis0 prefixlen 64 scopeid 0x2 ether 00:0d:b9:01:02:c8 media: Ethernet autoselect (none) status: no carrier supported media: media autoselect media 100baseTX mediaopt full-duplex media 100baseTX media 10baseT/UTP mediaopt full-duplex media 10baseT/UTP</vlan_mtu,polling></vlan_mtu></up,broadcast,running,promisc,simplex,multicast>

You have to enter the options in exactly the same way they are output here, without spaces.

But first do what Scott recommended, use a crossovercable and see if that makes a difference. Hardcoding settings usually causes just problems if not both sides are hardcoded.

@lsf:

But even with 2x cloaking (20mhz channel) it does 100mbit +.

Now that's impressive  :o.
Thanks for clarifying the Atheros 802.11N ;).
Anyways I've made up my mind.
I'm going for a net4801-60 and a CM9.
Maybe it's not THE mean machine but it sure will do the dirty work here at home.
In the future I may look out for 802.11N.
Cheers

Having the hard drive power down would only cause you a delay when it was needed and had to start back up. Hard drives really arn't loud these days. I ran an old 233 dell box with hard drive and it was barely audible unless up close.

However if you want it dead silent get an IDE to compact flash adapter and a compact flash card. I have this setup in my nokia ip330 box, costs around 30 bucks for the card and adapter. Works great.

Yes, we will look at adding this in a future version.

If someone wants to create a package, go for it and we'll commit it.

Don't think anyone has tried it, but if it works in FreeBSD, it can be made to work here.  You have to use the Developer's ISO, recompile the kernel to re-add your network interface, then add the interface type to /etc/interfaces.inc.

Might be a few other minor hacks required, but shouldn't be anything too major.

@sullrich:

Then I am not too sure at the moment.  I'll have to do a test install with Vmware shortly.

Just made the partition smaler.. then It works  ???
Thanks for helping anyway :)

Depends.

If you have just one AP - then there isn't much difference, although its simpler to mange the access (if restriction applies) on one system. Complicated Hotspot pages ? Forget about these AP’s, handle them from pFsense box.

If you need a bigger surface (multiple floors) to cover, then using the WRTG(S)’s as simple AP’s, and pFsense to manage the lot – will be simpler. Some ‘simple’ filtering has to be done on a per AP basis (think about the Network Neighbourhood from Windows  - and protecting the AP’s them self).

I’m using myself a pFsense PC-based system – and an OPT1 interface. The hotspot function is enabled on it – behind it is a switch and 5 AP’s (WRT54GS + Sveasoft firmware). This never failed on me.

That should work.

Yes, that's a pcengines WRAP and atheros based wireless cards. I have several of these units here running pfSense very well. See http://pfsense.com/mirror.php?section=/tutorials/wrap_install/wrap_install.htm how to set it up.

Hello again,

i figured out that the miniPCI modem has an pct303a chipset - a so called softmodem.

Martin